Monitoring of Structures During Repair of Underground Utilities
A collapse of underground utilities at a power plant required the constant monitoring of the surrounding structures during excavation and replacement of the damaged pipes. A computer-based...

Stability of Lift Slab Structure During Construction Stage
The lift slab structures impose stability problems during the construction phase. The process of constructing this type of structure requires placing the masses of the floor slabs at a...

Comparison of Bridge Deterioration Rates
This paper presents the results of a study of rates of deterioration of steel and prestressed concrete bridge superstructures. The results indicate that age is the primary determinant...

Progress in Reinforced Concrete Column Design: An Introduction
The Joint ASCE-ACI Committee 441 on Reinforced Concrete Columns is investigating a number of problems related to structural behavior and design of reinforced concrete columns. This paper...

Design of Lateral Steel in Columns
Lateral steel in columns is generally required for shear resistance, confinement of concrete and prevention of buckling of longitudinal bars. This paper is limited to the design of lateral...

Rational Limits for Longitudinal Steel in Concrete Columns
Current limits for the amount of longitudinal reinforcement in concrete columns were established more than 60 years ago. Commercial grades of reinforcement in 1930 were about half as strong...

High-Strength Concrete Columns: State of the Knowledge
This paper consists of reported information divided into two general categories, performance of High-Strength Concrete (HSC) columns under concentric loads, and combined axial and bending...

Progress in Reinforced Concrete Column Design
This paper reviews some of the design procedures used for both braced and unbraced frames constructed in reinforced concrete. The discussion refers to the problems of material and geometric...

Continuity in Precast Prestressed Concrete Girder Bridges
An experimental study conducted to evaluate the behavior of pretensioned bridge members made continuous with a cast-in-place concrete slab and diaphragm is summarized. In this study, the...

Use of Composite Timber-concrete Floors in Residential Buildings
Timber-concrete floors are widely used in the Gulf region for its resistance to hot and aggressive environment of the area. However, due to the fact that no shear connector is provided,...

Strength Variability of Wood Formwork Members
Failure of concrete formwork is one of the main causes of concrete construction failures. Among the main causes of formwork failure is inadequate strength. Currently there is no published...

Unified Code Provisions for Concrete Bridges
Provisions on limiting the flexural reinforcement adopted in the new AASHTO LRFD Specification for Bridge Design are summarized (1). They address minimum and maximum levels of reinforcement...

Guide for the Design of Prestressed Concrete Poles
With the aim of providing engineers with some basic tools and guidelines for the design of structures, the committee prepares code and policy changes, and to expand input of manufacturers...

ASCE GUIDE for Design of Guyed Transmission Structures
This paper describes the contents of a new ASCE guide for the selection and design of guyed electrical transmission structures. Guyed transmission structures present unique analysis and...

Design Guidelines for the Use of Debonded Strands
In this paper, presented are the flexural tests performed on beams containing debonded strands. Results show that debonded strands can be used reliably and safely, stipulating that the...

Development Length of Uncoated Prestressing Strand
The Federal Highway Administration is conducting ongoing research which investigates the development length of uncoated and epoxy coated prestressing strand in prestressed concrete members....

Mechanical Behavior of Dowels Embedded in Concrete
In this paper an experimental investigation on the behavior of dowels embedded in concrete is described. The dowel strength under monotonic forces with two different boundary conditions...

Cut and Cover Construction of the SSC Injector Tunnels
The injector system of the Superconducting Super Collider (SSC) constitutes the string of tunnels where protons are accelerated to near the speed of light and injected into the main collider...

High Strength Shotcrete and Concrete on the SSC Project
This paper addresses the technical aspects related to the use of high strength shotcrete and concrete on the Superconducting Super Collider (SSC) project. 7,000 psi shotcrete and 8,000...

An Overview of Shotcrete Usage on the SSC
Shotcrete has been widely used on the Superconducting Super Collider for initial support of tunnel excavations in both the strong and weak rock formations encountered. Different types...

 

 

 

 

Return to search